MENU SERVICE AND RESET FACTORY ALL TV LED LCD MADE IN CHINA
METHOD 1
Click on the TV VOL-key until the volume is turned down.
Press the MENU button on the remote control and select PICTURE
Press the sequence 6 5 6 8 to enter the FACTORY mode Pressing Sleep. Go to the next screen B / W BALANCE
FACTORY
This menu adjusts white balance and black or color temperature, using the CH + and CH-, you can choose the item and the VOL + and VOL-data can be modified.
To exit the service mode and save the settings by using the REVIEW button or the MENU key.
To change to B / W BALANCE ADJUST MENU OR, press on the remote control SLEEP key. Moving to the next screen: With this menu, you can make adjustments to geometry using the CH + and CH-, you can choose the item and the VOL + and VOL-data can be modified.
To exit this menu, press MUTE and so goes the ADJUST MENU ADJUST menu or one that allows us to adjust AGC, RF levels and color difference angles.To exit this menu, press MUTE and thus passes from the ADJUST ADJUST MENU 1 MENU 2, which allows adjustment of the horizontal width and position of the characters.
METHOD 2
Service mode for TV Kenix and Olympus with the remote.
It uses a service control or failing to uncover the original remote at the bottom there is a contact for a hidden key with this key enters the service mode.
Pressing the key contact enters service once FACTORY mode.
By pressing this key moves to the next submenu SET.
Pressing this key again passed to SETUP submenu.
, P To navigate the submenus are used in the P
, + And to vary the sub keys are used -
To record press the service button and then the SETUP mode.
Off with the remote control.
METHOD 3
Turn on the TV
DSP MEN U MUTE With remote control, run the following sequence SLEEP
The screen should display the service menu (Test mode).
With the CH (+) or CH (-) on the remote control parameters are changed
With the VOL (+) or VOL (-) on the remote control parameters are modified.
To exit the service menu or press SLEEP DSP.
Method 4
Method for entering the operating modes of micro TMPA8823 TV (For TV 14 "to 21") TMPA8859 (for TV 25 "to 34")
Note: The letter "S" means factory modes and can only be some tweaking. With letter "D" can adjust all parameters.
Follow these steps to enter the mode "S".
Press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enters the service mode "S".
60 VP choice this option must be set to "00". ) or CH ( To enter service mode "D" after entering the service mode "S" select with CH (
Then press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enters the service mode "D".
To review the current different channels without leaving the service mode, press the "DISPLAY", the disappearance of service parameters can change and change user settings.
Method 5
Operating mode for some models Kenix, Olympus and JWIN
Press the MENU button on the remote control then the sequence 6862 or 6483.
Press DISPLAY or MENU to change the menu.
Press DISPLAY or MENU several times and after the last drop out of service.
Off with the remote control to record.
Method 6
For TVs PREMIER
Item To change press PROG (+) or PROG (-).
To change the parameter value with the VOL (+) or VOL key (-).
To change all menu keys.
To exit and save, press MENU.
Method 7
For TVs JWIN
Press VOL (-) to achieve minimum volume and hold VOL (-)
Press DISPLAY or MENU exits the menu and service.
In case you do not get away with DISPLAY or MENU press each of the keys and hold VOL (-) until you exit the service menu.
Item To change press PROG (+) or PROG (-).
To change the parameter value with the VOL (+) or VOL key (-).
To exit, press MENU and turn off the TV with the remote control.
Method 8
For TVs RCA Chinese
Turn on the TV 20 minutes before making adjustments.
With lower the volume control until "00".
With the remote press MUTE to display on the screen.
Press and hold MUTE on the remote control.
Simultaneously press MENU on the TV's front panel and remain that way for 3 seconds until you enter the service mode.
Method 9
For other models Chinese RCA TVs
Follow these steps to enter the mode "S".
Press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enter the service mode "S".
To enter the mode "D" after entering the service mode "S" key to select OK.
4. )
METHOD 1
Click on the TV VOL-key until the volume is turned down.
Press the MENU button on the remote control and select PICTURE
Press the sequence 6 5 6 8 to enter the FACTORY mode Pressing Sleep. Go to the next screen B / W BALANCE
FACTORY
This menu adjusts white balance and black or color temperature, using the CH + and CH-, you can choose the item and the VOL + and VOL-data can be modified.
To exit the service mode and save the settings by using the REVIEW button or the MENU key.
To change to B / W BALANCE ADJUST MENU OR, press on the remote control SLEEP key. Moving to the next screen: With this menu, you can make adjustments to geometry using the CH + and CH-, you can choose the item and the VOL + and VOL-data can be modified.
To exit this menu, press MUTE and so goes the ADJUST MENU ADJUST menu or one that allows us to adjust AGC, RF levels and color difference angles.To exit this menu, press MUTE and thus passes from the ADJUST ADJUST MENU 1 MENU 2, which allows adjustment of the horizontal width and position of the characters.
METHOD 2
Service mode for TV Kenix and Olympus with the remote.
It uses a service control or failing to uncover the original remote at the bottom there is a contact for a hidden key with this key enters the service mode.
Pressing the key contact enters service once FACTORY mode.
By pressing this key moves to the next submenu SET.
Pressing this key again passed to SETUP submenu.
, P To navigate the submenus are used in the P
, + And to vary the sub keys are used -
To record press the service button and then the SETUP mode.
Off with the remote control.
METHOD 3
Turn on the TV
DSP MEN U MUTE With remote control, run the following sequence SLEEP
The screen should display the service menu (Test mode).
With the CH (+) or CH (-) on the remote control parameters are changed
With the VOL (+) or VOL (-) on the remote control parameters are modified.
To exit the service menu or press SLEEP DSP.
Method 4
Method for entering the operating modes of micro TMPA8823 TV (For TV 14 "to 21") TMPA8859 (for TV 25 "to 34")
Note: The letter "S" means factory modes and can only be some tweaking. With letter "D" can adjust all parameters.
Follow these steps to enter the mode "S".
Press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enters the service mode "S".
60 VP choice this option must be set to "00". ) or CH ( To enter service mode "D" after entering the service mode "S" select with CH (
Then press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enters the service mode "D".
To review the current different channels without leaving the service mode, press the "DISPLAY", the disappearance of service parameters can change and change user settings.
Method 5
Operating mode for some models Kenix, Olympus and JWIN
Press the MENU button on the remote control then the sequence 6862 or 6483.
Press DISPLAY or MENU to change the menu.
Press DISPLAY or MENU several times and after the last drop out of service.
Off with the remote control to record.
Method 6
For TVs PREMIER
Item To change press PROG (+) or PROG (-).
To change the parameter value with the VOL (+) or VOL key (-).
To change all menu keys.
To exit and save, press MENU.
Method 7
For TVs JWIN
Press VOL (-) to achieve minimum volume and hold VOL (-)
Press DISPLAY or MENU exits the menu and service.
In case you do not get away with DISPLAY or MENU press each of the keys and hold VOL (-) until you exit the service menu.
Item To change press PROG (+) or PROG (-).
To change the parameter value with the VOL (+) or VOL key (-).
To exit, press MENU and turn off the TV with the remote control.
Method 8
For TVs RCA Chinese
Turn on the TV 20 minutes before making adjustments.
With lower the volume control until "00".
With the remote press MUTE to display on the screen.
Press and hold MUTE on the remote control.
Simultaneously press MENU on the TV's front panel and remain that way for 3 seconds until you enter the service mode.
Method 9
For other models Chinese RCA TVs
Follow these steps to enter the mode "S".
Press the VOL (-) on the TV panel and without releasing press DISPLAY on the remote control and so enter the service mode "S".
To enter the mode "D" after entering the service mode "S" key to select OK.
4. )
Service Mode Tv LCD/LED China
- SUPRA STV-LC2277FL V6L10
- MAIN: T.VST29.61C 12296
- CPU: TSUMV59XU-Z1
- TUNER: CDT-3SP5I2-36
- SPI FLASH: W25Q32FVSIG
- PSU: HKC-PL01 REV: 3.0
- LED PANEL: LM215DA-T01
- Login to the remote service c MENU -1,1,4,7. Exit
- SUPRA STV-LC1985WL (V1M01)
- MAIN BOARD - 5800-A8M260-0020,
- SYSCON - MST6E181VS-LF-Z1,
- FLASH - MX25L3206,
- TUNER - HFT2-8F / 115CW,
- LED DISPLAY - E185SG01.
- Login to the service: SOURCE - 3,1,9,5.
- SUPRA STV-LC42590F (V2L09)
- MAIN BOARD-350016386,
- Flash 25fl032,
- LCD panel LC420WUE (SC) (V1)
- Enter the service mode - with the remote control, press "MENU" - dial 2008 - exit - EXIT.
- Supra LCD model STV-LC1522W
- Main CVMV26L-A-20
- Serial Flash F40-100CGP
- eeprom K24C32
- Tuner F21Wt-3BAR-E
- audio TDA1517P
- SYSCON TSUMV26KE-LF
- LK-IN150205A
- Panel M156MWR1
- Login to the service with the remote control: "Menu", "Red", "Green", "Yellow", "Cyan"
- SUPRA STV-LC2437AFL (V2L07)
- MAIN BOARD-CV182L_B,
- SPI FLASH-W25Q32,
- TUNER-CDT-3SP512-37,
- LED DISPLAY-M240HW02
- Login to the service - INPUT-2580.
- SUPRA STV-LC2222WD (V1I12)
- Section TV:
- MAIN BOARD-SP208ESA HK-7050A-V2.08-E,
- SPI FLASH-EN25T80 (U7),
- EEPROM-24C32 (U9),
- TUNER-TNF931D-BFR1,
- LCD MATRIX-CLAA215FA.
- Section DVD: MPEG BOARD-B.SPDM7B,
- MPEG-SPHE8202TQ (U25),
- SPI FLASH-EN25T80 (U5),
- Driver-D5888S,
- Optics-HOP-120X.
- Login to the service - MENU-7050.
- SUPRA STV-LC39950FL (V1M01)
- MAIN BOARD 35017414 REV-01
- SYSCON MT8227AAKU (BMSL),
- SPI FLASH W25Q32,
- LED DISPLAY CMI-V390HJ1-P02.
- Login to the service-MENU-2008.
- SUPRA STV-LC32K800WL (V1M02)
- MAIN BOARD T.MS18VG.72 T.VST59.A5,
- SYSCON TSUMV59XE,
- SPI FLASH W25Q32,
- TUNER CDT-3NP5 / 1-10,
- LED DISPLAY LM315TA-T01.
- Login to the service MENU-1147.
- SUPRA STV-LC2477FLD (V5L09)
- SECTION TV:
- MAIN BOARD-CV181L-Y,
- SPI FLASH-W25Q32,
- TUNER-CDT-3SP512-37,
- LED DISPLAY-V236H1-P01.
- SECTION DVD:
- MPEG BOARD-GM-CH1089J-V1.2,
- MPEG-MT1389DE (JDAL),
- SPI FLASH-KH25L1606,
- Driver-CD5888CB,
- Optics-SF-HD850
- Login to the service - INPUT-2580
- SUPRA STV-LC2477FLD (V6L10)
- MAIN BOARD-T.VST.29.61C,
- SYSCON-TSUMV59XU-Z1,
- SPI FLASH-GD25Q32,
- TUNER-CDT3SP512-36,
- LED DISPLAY-V236H1-P01.
- SECTION DVD:
- MPEG BOARD-GM-CH1089J-V1.2,
- MPEG-MT1389DE (JDAL),
- SPI FLASH-KH25L1606,
- Driver-CD5888CB,
- Optics-SF-HD850.
- Login to the service: MENU-1147.
- SUPRA STV-LC19810WL (V4L12)
- MAIN BOARD-Y.VST59.62,
- SYSCON-TSUMV59XU,
- SPI FLASH-GD25Q32,
- TUNER-CDT-3NP5 / 1-10,
- LED DISPLAY-LS185AWTNM
- Login to the service - MENU-1147.
- SUPRA STV-LC17250FL (V1L02) W25Q32
- MAIN BOARD CV182L_B,
- SPI FLASH W25Q32,
- TUNER CDT-3SP512-37,
- LED DISPLAY N164HGE-L12.
- Login to the service INPUT-2580.
- SUPRA STV-LC24410FL (V2M04)
- MAIN BOARD-T.VST29.61C,
- SYSCON TSUMV59XE-Z1,
- SPI FLASH W25Q32,
- TUNER CDT-3SP512-36,
- LED DISPLAY HM236WU3-100.
- Log in servis-- MENU-1147.
- Addition to this topic:
- - Firmware version of V2M04 and V2L10
- - Interchangeable
- - Changes the OSD.
- Supra STV- LC2204W
- CPU MST719DU-LF
- MAIN: JUG7.820.531-3, 24LC32, TEA2025B,
- Tuner: TAF6-C2I21V
- Login to the service: INPUT, 3,1,3,8
- SUPRA STV-LC42740FL (V1L11)
- MAIN: 35016445 REV-02
- SYSCON: MT8227AAKU (BMSL),
- SPI FLASH: W25Q32.
- Log in SM: MENU-2,0,0,8.
- SUPRA STV-LC42740FL (V1L11)
- MAIN: 35016445 REV-02
- SYSCON: MT8227AAKU (BMSL),
- SPI FLASH: W25Q32.
- Log in SM: MENU-2,0,0,8.
- SUPRA STV-LC42590F (V2L06)
- MAIN: 35016386,
- SYSCON: MST6E182VSA-LF-Z1,
- SPI FLASH: S25FL032P (N504),
- EEPROM: 24C64,
- TUNER: AFT7 / W127,
- LCD PANEL: LC420WUE.
- Log in SM: MENU - 2,0,0,8.
- SUPRA STV-LC42590F
- Enter and exit the factory menu:
- Press "MENU" button on the remote control and then press "2", "0", "0", "8" in 3 seconds, and enter the factory menu in success.
- Press "MUTE" button to exit the factory menu.
- Press the "MENU" in the operation mode "2", "0", "0", "8" for 3 seconds and enter the factory menu success.
- Byhod from factory menu = MUTE =
- SUPRA STV-LC2725AFL (V5L11)
- MAIN: T.VST59S.73,
- SYSCON: TSUMV56XES-Z1,
- SPI FLASH: GD25Q32,
- TUNER: CDT-3NP5 / 1-10,
- LED PANEL: M270HGE-L21.
- Enter the service mode: MENU -1,1,4,7.
- SUPRA STV-LC22820FL (V4L10)
- MAIN: T.VST59.62,
- SYSCON: TSUMV59XU-Z1,
- SPI FLASH: GD25Q32,
- TUNER: CDT-3NP5 / 1-10,
- LED PANEL: M215HGE-L10.
- Login to the service MENU - 1,1,4,7
- SUPRA STV-LC3225AWL version (V4L06)
- panel TB315B201
- MAIN CV182H-E (percent under the radiator, but probably TSUMV26KU-LF)
- flush 25Q32bvs
- Tuner CDT3SP512-37
- Power BSF-PI320201B (LD7575PS basic and KE 1 35 written on Shimkiv bowls)
- Entrance to the service menu - 2,5,8,0.
- SUPRA STV-LC3225AWL (V7L11)
- MAIN: TP.VST59.P83,
- LED PANEL: TX315B3HB-MD2,
- SYSCON: TSUMV59XU,
- SPI FLASH: W25Q32,
- TUNER: CDT-3NP5 / 1-10.
- Enter the service mode: MENU -1,1,4,7.
- SUPRA STV- LC39520FL (V1M04)
- MAIN BOARD: T.MS18VG.72 T.VST59.A5,
- SYSCON - TSUMV59XE,
- SPI FLASH - W25Q32,
- TUNER- CDT-5NP5 / 1-10,
- LED DISPLAY- V390HJ1-P02.
- Login to the service-MENU-1147.
- SUPRA STV-LC32740WL (V1L08)
- MAIN: 35016408 REV-01
- SYSCON: MT8227AAKU (BMSL),
- SPI FLASH: W25Q32,
- LED PANEL: HV320WX2-201.
- Enter the service mode: MENU - 2,0,0,8.
- SUPRA STV-LC2622W
- Main T.MT8223.3B
- CPU under the radiator
- Flash 25Q16VSIG (U7)
- EEPROM FT24C32A (U13)
- Matrix M260TWR1
- Tuner F20WT-3DDR-E
- Sound R2A15122FP (10 watts x 2 channels / 8 Ohm / 24 V)
- HDMI IT6633E-P
- Multiplexer / demultiplexer CBT3257AD, CD4052
- Service MENU - 1147
- SUPRA STV - LC3217W (V5L11)
- main: T.MS.18VG.81B,
- SPI flash: W25Q32,
- TUNER: CDT-3SP512-36,
- LCD PANEL: LM315TA-T01.
- Enter the service mode: MENU-1,1,4,7.
- SUPRA STV-LC1922W (V2J08)
- MAIN BOARD-CVMV26L-A-20,
- SPI FLASH-EN25F40,
- EEPROM-24C32,
- SYSCON-TSUMV26KE-LF,
- TUNER-F21WT-3BAR-E,
- LCD MATRIX-MT185GW01 V.2.
- Login to the service-INPUT-VGA, INPUT-2580.
- SUPRA STV-LC1977WL (V6L10)
- Main: T.VST29.61C,
- LED PANEL: M185BGE-P02,
- CPU: TSUMV59XU-Z1,
- SPI flash: GD25Q32,
- TUNER: CDT-3SP512-36.
- Enter the service mode: MENU-2.5.8.0.
- SUPRA STV-LC19810WL (V2L07)
- MAIN CV182L_B
- Under the CPU heatsink
- SPI FLASH W25Q32
- TUNER CDT- 3SP512-37
- LED PANEL TB190B300-A
- CM INPUT 2.5.8.0.
- SUPRA STV LC2677WL (V5L11)
- MAIN BOARD T.MS18VG.81B,
- FLASH W25Q32,
- TUNER CDT-3SP512-36,
- LED DISPLAY V260B2-P03.
- After the firmware is NECESSARY to enter the service menu (1147), initialize the INIT TV,
- then turn off the power, wait for the extinction of the ice indicator, turn on the power, and everything is OK.
- SUPRA STV-LC19810WL (V2L07)
- MAIN CV182L_B
- Under the CPU heatsink
- SPI FLASH W25Q32
- TUNER CDT- 3SP512-37
- LED PANEL TB190B300-A
- CM INPUT 2.5.8.0.
- SUPRA STV-LC2622W (V2J12)
- MAIN BOARD T.MT8223.3B,
- SPI FLASH W25Q16,
- EEPROM 24C32,
- TUNER F20WT-3DDR-E,
- LCD MATRIX M260TWR1.
- Login to the service MENU-1147.
- SUPRA STV-LC16830WL V1M04
- MAIN T.VST59.62
- CPU TSUMV59XU-Z1
- SPI FLAS GD25Q32
- TUNER CDT-3NP5 / 1-10
- LED PANEL B156XTN02.2
- Enter the service mode: MENU -1.1.4.7
- SUPRA STV-LC22810FL V4M01
- MAIN: T.VST59.62 CPU: TSUMV59XE
- SPI FLASH: W25Q32
- TUNER: CDT-3NP5 / 1-10
- LED PANEL: M215HGE-L21
- Enter the service mode: MENU - 1,1,4,7.
- SUPRA STV-LC32520WL (T.MS18VG.72T.VST59.A5)
- CPU / MCU: TSUMV59XE-Z1
- EEPROM / FLASH: 25Q32
- Screen BOE HV320WX2-261
- Login to the service: Menu-1-1-4-7
- SUPRA STV-LC32520WL V2M12
- MAIN CV59SH-J
- CPU TSUMV59XUS-Z1
- SPI FLASH GD25Q32
- TUNER CDT3NP512-10
- LED PANEL HK315WLEDM-HHZ5H
- Login to the service; SOURSE- 2.5.8.0.
- SUPRA STV-LC32S650WL (V1L09)
- MAIN T.MS6M182.81B-1
- SPI FLASH GD25Q32
- CPU under the radiator
- TUNER CDT-3SP512-36
- LED PANEL MT3151A03-1
- SMART (ANDROID)
- MAIN B.AML8726.3B
- CM MENU-1.1.4.7.
- SUPRA STV-LC32510WL V2M11
- MAIN CV59SH-J
- CPU TSUMV59XES
- SPI FLASH GD25Q32
- TUNER CDT-3NP512-10
- LED PANEL LC320EXJ-SEE
- T-CON 6870C-0414A
- CM INPUT-2580.
- SUPRA STV-LC3265FL (V4L09)
- MAIN BOARD T.MS18VG.71A,
- SPI FLASH GD25Q32,
- TUNER CDT-3SP512-36,
- T-CON V315H3-CPE6,
- LED DISPLAY TC315F303.
- Login to the service-MENU-1147.
- SUPRA STV-LC32T662WL V1N05
- MAIN BOARD 40-T31TOT-MAB2HG
- CPU under the radiator
- SPI FLASH W25Q64
- LED PANEL LVW320CSOT E45 V16
- Enter the service mode
- MENU-CONTRAST - 9735 or (1950)
- Entering the menu - in the audio settings - to find a balance - we collect from the remote control without long pauses, "0532"
- SOURSE-PC-MENU-2580, MENU-2580, MENU-2008, MENU-9883, MENU-1147, MENU-7050, MENU-0000, SOURSE-3138,
- MENU-1234, MENU-КОНТРАСТ-9735, MENU-7168, MENU8202, SOURSE-3195, MENU-9527, MENU-1950, MENU-8202,
- In the video we make our money MENU - 0000, MENU-8500, MENU-9301
- Generally speaking, all these codes and SOURSE MENU mode AV PC because in TV mode by pressing the MENU channel disappears
- Clamped VOL- MENU ON TV network and other key combinations did not help.
- SUPRA STV-LC32790WL
- Chassis T.MS18VG.72)
- Problem:
- Arts inverted, negative
- MENU 1147 put LVDS MAP 1
- SUPRA STV-LC2225WL V9M03
- MAIN T.VST59.62
- PROCEED TSUMV59XU-Z1
- PANEL LS215BFTNM
- TUNER CDT-3NP51-10
- MENU-1147
- SUPRA STV-LC32T420WL V1N09
- 40-MT31BP-MAA2LG
- LVW320CSOT E155 V2
- MENU-PICTURE-CONTRAST-9735 (or 1950)
- ID PROJECT 110
- SUPRA STV-LC3211W
- JUG7.820.265-2
- Press the MUTE button on the remote
- Next, press Menu, and go to the Settings window Sound Sound
- In the move to the Sound adjustment Balance arrow P -
- Next to the column Balance press Vol +,
- with the appearance of scales alternately pushing 3,1,3,8
- TCL
- PRESS THE MENU and enter code 1815
- SHARP
- Press the Menu and enter code 1999
- COOCAA
- press the Source and enter code 2580
No comments:
Post a Comment